IMCInter Module Communication
v5.5.11

Reference

Message groups

A field whose message type is a group accepts any member of the group.

#Maneuver

36 members. Accepted by VehicleCommand.maneuver, PlanManeuver.data, ManeuverResumed.man_list.

IDMessageDescription
495AlignmentAn "Alignment" is a maneuver specifying a movement of the vehicle to a target waypoint intended to control activation of an IMU/INS in order to start aligning navigation for more…
493AutonomousSectionThis maneuver triggers an external controller that will guide the vehicle during a specified duration of time or until it relinquishes control using (ManeuverDone).
472CommsRelayIn this maneuver, a vehicle drives to the center of two other systems (a, b) in order to be used as a communications relay.
475CompassCalibrationThis maneuver is a mix between the Loiter maneuver and the YoYo maneuver.
473CoverAreaGiven a polygonal area, generates trajectories to cover the area.
465CustomManeuverThe Custom Maneuver message may be used as specification of a very specific maneuver not covered by the IMC scope.
483DislodgeA "Dislodge" is a maneuver ordering the vehicle to attempt a series of thruster operations that will hopefully get it unstuck from an entangled condition.
486DropA "Drop" is a maneuver specifying a movement of the vehicle to a target waypoint.
454IdleManeuverCauses the vehicle to stay idle for some time.
490ImageTrackingA "ImageTracking" is a maneuver specifying a particular heading to the detected object.
462ElevatorThe Elevator maneuver specifies a vehicle to reach a target waypoint using a cruise altitude/depth and then ascend or descend to another target altitude/depth.
496FollowCommandThis maneuver follows a direct command given by an external entity.
457FollowPathManeuver constituted by a list of Path Points.
494FollowPointThis maneuver behaves by following a point.
478FollowReferenceThis maneuver follows a reference given by an external entity.
463FollowTrajectoryManeuver constituted by a list of Trajectory Points.
477FormationPlanExecutionA "Formation Plan" is a maneuver specifying a plan for a team of vehicles.
450GotoA "Goto" is a maneuver specifying a movement of the vehicle to a target waypoint.
492LandAutomatic landing on the ground, for UAVs.
485LaunchA "Launch" is a maneuver specifying a movement of the vehicle to a target waypoint after being launched from a ship or pier.
453LoiterThe Loiter maneuver makes the vehicle circle around a specific waypoint with fixed depth reference.
455LowLevelControlLow level maneuver that sends a (heading, roll, speed, ...) reference to a controller of the vehicle and then optionally lingers for some time.
499MagnetometerMagnetometer calibration maneuver (i.e: one square pattern in one direction, a second square in the opposite direction)
721PaddlingThe Paddling maneuver makes the vehicle move by using its fins (paddles).
451PopUpThe Pop Up maneuver makes the vehicle come to the surface at a specific waypoint.
456RowsRows maneuver (i.e: lawn mower type maneuver)
488RowsCoverageRows coverage (i.e: lawn mower type maneuver) but with adaptive cover
489SampleA "Sample" is a maneuver specifying a movement of the vehicle to a target waypoint.
487ScheduledGotoThis maneuver is used to command the vehicle to arrive at some destination at a specified absolute time.
2046SetPoseA "SetPose" is a maneuver specifying a movement of the vehicle to a specific pose (position and orientation).
461StationKeepingThe Station Keeping maneuver makes the vehicle come to the surface and then enter a given circular perimeter around a waypoint coordinate for a certain amount of time.
720StationKeepingExtendedThe Station Keeping Extended maneuver makes the vehicle come to the surface and then enter a given circular perimeter around a waypoint coordinate for a certain amount of time.
491TakeoffAutomatic takeoff for UAVs.
452TeleoperationThe Teleoperation Maneuver lets the vehicle be controlled by an external human operator.
466VehicleFormationCoordinate maneuver using two or more cooperating systems.
459YoYoA "yo-yo" is a maneuver specifying a vehicle movement to a target waypoint in which depth/altitude varies along the way between two values with a desired pitch angle.

#ControlCommand Control Command

7 members. Accepted by LowLevelControl.control.

IDMessageDescription
401DesiredZDesired Z reference value for the control layer.
400DesiredHeadingDesired Heading angle reference value for the control layer.
403DesiredRollDesired Roll angle reference value for the control layer.
404DesiredPitchDesired Pitch angle reference value for the control layer.
402DesiredSpeedDesired Speed reference value for the control layer.
406DesiredPathPerform path control.
415DesiredThrottleDesired throttle e.g.

#RemoteData

2 members. Accepted by HistoricData.data.

IDMessageDescription
188RemoteCommandCommand to remote system.
186HistoricSample

#TypedEntityParametersOptions

2 members. Accepted by QueryTypedEntityParameters.parameters.

IDMessageDescription
2017TypedEntityParameterEntity parameter with all the data that defines an entity parameter.
2036TypedEntityParameterEditorThis message is used to describe the ValuesIf content of a TypedEntityParameter.